Sea Fever Yacht for Sale | 48 Sabre Yachts Sarasota, FL

Cruising Speed: 29 kn
Maximum Speed: 33 kn
Beam: 15' 4''
Hull Material: Fiberglass
Max Draft: 4' 1''
Fuel Tank: 1 x 525|gallon
Fresh Water: 1 x 160|gallon
Holding: 1 x 70|gallon
Heads: 2

* Dark grey hull color (Shark).
* Anti-skid color (fore & side decks, aft cockpit , and recessed area of swim platform). * FRP molded mast & separate radar platform for sedan hardtop.
* Teak decking in aft cockpit including steps.
* Kahlenberg dual chrome horns.
* Sureshade color Oyster.
* Custom teak cockpit table. Change shape of cockpit table to be rectangular and 6" longer.
* Delete standard teak toe rails. Install 9" Skene chocks to forward cleats.
* Reverso oil change system.
* Stand alone 3000W inverter and separate 100A battery charger.
* Central vac system with (2) outlets and a 32' expandable hose.
* Searchlight dual beam mounted on hard top mast.
* Install Sabre electronics prewire harness.
* Install Additional 120V Outlet in cockpit on vertical surface behind the swing door.
* 9.5" Innerspring mattress on master berth.
* Install a rain shower head and shower wand in master shower.
* Custom main salon layout with centerline hatch and port side.
* Build a bottom in the TV cabinet so it can be used as a chart kit holder.
* Build a long settee with long end table.
* Compass rose and high gloss top on end table.
* Modify the pan in the Utility Room to create a landing.
* Reverse the stbd L settee so the aft facing seat is directly behind the Stidd seats.
* Build a 40" TV outboard of the settee.
* Build an end table on the aft end of the settee with a high gloss finish and compass rose. * Add hydraulic lift to the utility room hatch in main salon sole. Install the lift on the fwd end of the utility room hatch so it is out of the way as much as possible. Install button at the helm.
* Splendide washer & separate dryer sidexside in utility room w/two drawers below *Hanging rod and custom shelving in custom Utility Room.
* Spare props. One set.

Modified Deep “V” Planing hull design, with pod drive tunnels for Cummins Zeus drives
14º deadrise at transom, 23º deadrise amidships.
ISO NPG white gelcoat w/vinylester backup resin.
Bottom, topsides and transom VIP resin infused biaxial E-glass with Corecell SAN foam core.
Stringer system biaxial E-glass with foam core.
Resin Infused E-glass swim platform with molded-in anti-skid surface.
Hull side rubbing strakes.
White PVC rub rail with stainless steel cap.
Painted (Urethane) double boot top.
Gold recessed cove stripe.

ISO NPG gelcoat.
VIP resin infused biaxial E-glass with balsa core.
Molded-in anti-skid deck surfaces.
Companionway door to port.
Sliding windows in salon on cabin sides.
Electric opening window in salon aft bulkhead.
Hinged access door to side deck at helm.
Flush, outward opening, transom door with latch.
Anchor locker with slam latch.
Large lazarette/engine room access hatch in cockpit sole with compression latches.
Integrated Sure Shade system over cockpit

1 1/4″ Diameter type 316 stainless steel perimeter rail system.
(6) 12” Stainless steel cleats: two forward, four mid-ship.
(2) Stainless steel bollard cleats aft
(2) Stainless 12″ cleats on cockpit coaming on centerline
10” Stainless steel cleat to starboard of windlass as anchor rode tie off.
(4) Custom cast stainless steel mid-rail line chocks.
Custom cast stainless steel skene chocks forward.
Custom stainless steel bow pulpit with dual anchor roller for 44lb CQR or Delta anchor and “lunch hook”.
Quick anchor windlass, electric rope-chain type
Teak flag staff and socket on taffrail.
Burgee staff on bow pulpit.
(6) Low Profile stainless steel hatches w/screens.
(6) Custom stainless steel opening port lights.
Teak toe rails.
Teak cabin-side eyebrow.
Teak table in cockpit
Custom cast stainless steel “SABRE” logo
Raw water washdown system at the bow.
Kahlenberg single chrome air horn

Hinged access door to starboard side deck.
Dual Volvo-Garmin 8617 Multi-Function Displays (MFDs) w/ Separate SD Card Readers.
Volvo-Penta Autopilot w/ Joystick Driving.
Volvo-Penta IPS Plus Joystick Controller on Stidd Armrest.
Twin Lever Shift & Throttle Control (EVC-E) w/ Single Lever & Cruise Control Software.
Triple windshield wipers w/ multiple speed settings.
Windshield washers plumbed from the fresh water system.
Ritchie Compass.
Switch controls for horn, running lights, anchor light, engine room blowers, & bilge pumps.
Custom teak steering wheel w/ tilt helm & Sabre logo.
Twin Stidd N Series helm seats w/ Ultraleather® fabric mounted on a cherry cabinet
NMEA 2000 backbone

Island berth athwartship layout with 9″ foam mattress and laminated trim.
Hull side deadlight over head board
Shoji style passageway and closet doors
Shoji style portlight screen panels
Cherry hull ceilings.
Drawers under berth and in bulkhead aft of berth.
(2) hanging lockers fore and aft of bed.
Teak and holly sole.
Sound deadening soft headliner panels.
Sliding door to master head compartment

Private access from master stateroom
Custom tile in WC and shower sole
Glass vessel style sink
High gloss finish over solid cherry counter.
Vanity cabinet below sink
Storage outboard
Mirror above vanity, cherry framed
Separate shower stall with clear bi-fold enclosure and glass tile accent wall within
Electric shower sump pump
Opening port to side deck
Deck hatch with blind/screen overhead
Ventilation blower
Stainless steel towel bars

Spacious island berth, with 6″ mattress and laminated trim.
Cherry hull ceilings.
Drawers under berth, A/C return grille beside.
Storage lockers, drawers and shelves.
Teak and holly sole.
Sound deadening soft headliner panels.
Private access to forward head and shower

“L” settee to starboard, 5” foam cushions, with storage and Sabre tool drawer under.
High Gloss finished table with hi-low pedestal and angled slide mechanism. Lowers to coffee table height.
Entertainment unit to port including a flat screen LCD TV 32” on lift with DVD player
Sound deadening, soft headliner panels.
Raised mates L-shaped settee to port of helm
Hinged stainless steel door to cockpit
Electrically operated window aft of L-settee
Deep chart table forward of L-settee seat port
Fiddles at nav station

Twin Garmin Glass screens.
Garmin 12KW XHD Radar w/ pedestal.
Garmin 4' Antenna.
Icom M330G VHF.
Garmin GXM54 Sirius.
Airmar B060 Transducer.
Direct TV Receiver.
2 - SHA 5225X7 UNH Antenn's.
2 - SHA 4187 Antennae Mounts.
Garmin 12 to 8 Pin Adaptor.
KVH TracVision TV3 Antenna.
KVH Tracvision Dummy Dome.
Wave MBR550 Router.
Wave Ext Cell Antenna.
Wave Rogue Pro Antenna.

* Custom teak cockpit table. Change shape of cockpit table to be rectangular and 6" longer.

* Delete standard teak toe rails. Install 9" Skene chocks to forward cleats.
* 9.5" Innerspring mattress on master berth.

* 9.5" Innerspring mattress on master berth.
* Install a rain shower head and shower wand in master shower.
* Custom main salon layout with centerline hatch and port side.
* Build a bottom in the TV cabinet so it can be used as a chart kit holder.
* Build a long settee with long end table.
* Compass rose and high gloss top on end table.
* Modify the pan in the Utility Room to create a landing.
* Reverse the stbd L settee so the aft facing seat is directly behind the Stidd seats.
* Build a 40" TV outboard of the settee.
* Build an end table on the aft end of the settee with a high gloss finish and compass rose. * Add hydraulic lift to the utility room hatch in main salon sole. Install the lift on the fwd end of the utility room hatch so it is out of the way as much as possible. Install button at the helm.

* Spare props. One set.