- Beam: 12' 0''
- Hull Material: Fiberglass
- Max Draft: 4' 6''
- Displacement: 12,566 lb
- Fuel Tank: 1 x 34|gallon
- Fresh Water: 1 x 83|gallon
- Holding: 1 x 21|gallon
- Cabins: 2
- Heads: 1
2011 Beneteau Oceanis 34 “Boat Pour” — Shoal-Draft Cruiser with Low-Hour Yanmar, Updated Electrical System, Air Conditioning, AIS and Two-Cabin Layout
Introduction and Key FeaturesBoat Pour is a well-maintained 2011 Beneteau Oceanis 34 located in Pensacola, Florida, and currently offered at $105,000.
Designed by Jean-Marie Finot of Finot-Conq with an interior by Nauta Design, the Oceanis 34 combines responsive sailing performance, a manageable sail plan, shallow-water cruising capability, and accommodations normally associated with a considerably larger yacht.
Her two-cabin, one-head interior sleeps up to six and offers approximately 6'3" of headroom, reverse-cycle air conditioning, a complete galley, a proper navigation station, generous storage, and excellent natural light through opening ports and hatches.
Above deck, Boat Pour offers a large cockpit, walk-through transom, swim platform, shoal-draft keel, classic mainsail configuration with a Tides Marine Strong Track, furling genoa, Harken self-tailing winches, and lines arranged for efficient short-handed sailing.
A pre-purchase condition and valuation survey was completed in August 2024. At that time, the surveyor described the vessel as being in above-average condition. Accessible hull, deck, rudder, keel, structural, steering, mechanical, and electrical components were inspected. The survey reported no excessive moisture, deck soft spots, hull blistering, delamination, or evidence of previous structural hull damage.
Key FeaturesTwo-cabin, one-head cruising layout
Sleeps up to six
Approximately 6'3" interior headroom
Shoal-draft keel with approximately 4'6" draft
Yanmar 3YM30 diesel with approximately 390 hours
CruiseAir 16,000 BTU reverse-cycle air conditioning
Upgraded electrical distribution panel installed in 2026
Three Group 31 AGM batteries replaced in October 2024
Hitachi 80-amp high-output alternator
Mastervolt battery charger
ProWatt 600-watt inverter
Dual 30-amp shore-power service
Garmin GPSMAP 1243 multifunction display
Raymarine wheel-pilot autopilot
Raymarine sailing instruments
Standard Horizon Matrix VHF with helm RAM microphone
AIS transceiver
Fully battened Dacron mainsail
Tides Marine Strong Track mainsail system
120% Dacron roller-furling genoa
Profurl headsail furling system
Harken self-tailing winches
Rigid boom vang
Whisker pole
Blue bimini
Opening companionway doors in place of traditional drop boards
Bruce 33-pound anchor with chain and rode
Revere four-person liferaft, with reinspection required
Bottom painted in 2023
Bottom cleaned approximately every six weeks
August 2024 survey available
Market appraisal, owner’s manual, and parts information available upon request
CE Certified, Classification A-6
Denison Yachting - San Francisco is pleased to assist you in the purchase of this vessel. This boat is centrally listed by Preferred Yachts.
Denison Yacht Sales offers the details of this yacht in good faith but can’t guarantee the accuracy of this information nor warrant the condition of this boat for sale. This yacht for sale is offered subject to prior sale, price change, or withdrawal from that yacht market without notice. She is offered as a convenience by this yacht broker to its clients and is not intended to convey direct representation of a specific yacht for sale.
The Beneteau Oceanis 34 remains one of the most appealing modern cruising boats in this size range because it successfully balances sailing performance, interior comfort, shallow draft, and ease of ownership.
Boat Pour is especially well suited to a cruising couple, small family, or sailor seeking a manageable platform for Gulf Coast cruising, the Florida Keys, the Intracoastal Waterway, or the Bahamas. Her 4' 6" shoal draft expands anchoring and cruising options, while her bridge clearance of approximately 50' 8" make her relevant for many coastal and ICW itineraries.
Her traditional fully battened mainsail, supported by a Tides Marine Strong Track, provides a straightforward and efficient sail-handling arrangement. The 120% furling genoa, Harken self-tailing winches, traveler, rigid vang, rope clutches, wheel steering, and cockpit-led controls allow her to be sailed comfortably with limited crew.
Below, the Nauta-designed interior is warm, bright, and intelligently arranged. The two private cabins, convertible salon seating, full galley, enclosed head, navigation station, air conditioning, and generous water capacity make extended stays aboard practical and comfortable.
Several meaningful updates enhance her appeal, including the upgraded 2026 electrical panel, three Group 31 AGM batteries installed in October 2024, an 80-amp high-output alternator, Garmin multifunction display, AIS, reverse-cycle air conditioning, and LED lighting.
The August 2024 survey provides additional insight into the vessel’s condition at that time. The surveyor characterized the interior as generally above average for the vessel’s age and type. Accessible deck areas were percussion sounded and moisture-meter tested, with no soft spots, delamination, or excessive moisture reported. The hull sides were found to retain a high-gloss finish, with no signs of previous structural damage noted.
Boat Pour is berthed at Bayou Grande Marina at Pensacola Naval Air Station in Pensacola, Florida.
Boat Pour features Beneteau’s desirable two-cabin, one-head arrangement with accommodations for up to six.
The interior was designed by Nauta Design and makes excellent use of the boat’s 12-foot beam. Fixed windows, opening ports, overhead hatches, light-colored headliners, and warm cabinetry create an open and inviting atmosphere.
Interior headroom is approximately 6'3".
Main SalonThe main salon features a U-shaped settee to port and a longitudinal settee to starboard. The port dinette surrounds a centerline table attached at the compression post. The table has two folding leaves, allowing it to remain compact while underway and expand for meals or entertaining.
The salon seating can provide two additional single berths, bringing total sleeping capacity to six.
Additional salon features include:
Blue cushions patterned with white sailboats
Dinette table with two folding leaves
Port and starboard settees
Convertible salon sleeping accommodations
Flat-screen television
Fixed and opening ports
Opening overhead hatch
LED lighting
Storage behind and beneath seating
Storage lockers above the settees
No-maintenance synthetic veneer cabin sole
CruiseAir reverse-cycle air conditioning
CO detectors
Approximately 6'3" headroom
The private forward cabin serves as the primary owner’s stateroom and includes:
V-berth
Marine mattress
Port and starboard storage
Hanging lockers
Opening overhead hatch
Natural light and ventilation
Privacy door
Water tank located beneath the berth
The private aft guest cabin is entered to port, aft of the galley.
Features include:
Large full-width double berth
Athwartships sleeping arrangement
Hanging locker
Storage
Opening port
Standing and seated space near the cabin entrance
Access panels to mechanical and electrical components beneath the berth
The enclosed head is located aft to starboard and includes:
Electric marine toilet
Molded sink and vanity
Separate shower area
Handheld shower fixture
Hot and cold pressure water
Storage beneath and around the vanity
Approximately 21-gallon holding tank
Y-valve
Macerator/discharge pump
Privacy door
Auxiliary propulsion is provided by a Yanmar 3YM30 naturally aspirated, three-cylinder marine diesel.
EngineManufacturer: Yanmar
Model: 3YM30
Configuration: Inboard diesel
Horsepower: 29 HP
Kilowatts: Approximately 21.63 kW
Engine hours: Approximately 372
Serial number: 116851
Engine location: Centerline beneath the companionway
Freshwater-cooled
Raw-water sea strainer
Water-separating fuel filter
Engine-mounted secondary fuel filter
Wet exhaust system
Single-lever engine control
Tachometer and engine alarms
Adjustable engine mounts
Fiberglass engine beds and structural stringers
During the August 2024 sea trial, the engine reportedly operated smoothly without obvious vibration, with good cooling-water discharge and responsive handling. The vessel reached approximately 7 knots at about 3,200 rpm during the recorded wide-open-throttle portion of that sea trial.
Transmission and PropulsionYanmar/Kanzaki transmission
Model KM2P-1
Direct-drive shaft configuration
Stainless-steel propeller shaft
Three-blade fixed bronze propeller
Volvo water-injected dripless shaft seal
Cutlass bearing and external bearing carrier
Wheel steering
Emergency tiller connection and emergency tiller
Mechanical wheel steering uses a stainless-steel wheel, chain-and-cable linkage, sheaves, and a radial drive at the rudderpost.
The August 2024 survey found the accessible steering components sound, properly adjusted, and operating freely. The helm was described as responsive during sea trial.
Additional Mechanical EquipmentCruiseAir 16,000 BTU reverse-cycle air conditioning
Digital air-conditioning controls
115V and engine heat-exchanger water heater
Approximately 25-liter/6.6-gallon Quick Nautic Boiler water heater
12V electric bilge pump
Manual cockpit-operated bilge pump
Shower sump pump
Freshwater pressure pump
Accumulator tank
Cockpit shower
Electric marine head
Y-valve
Macerator/discharge pump
Plastic fuel tank
Plastic freshwater tank
Plastic holding tank
Water-separating fuel filter
Fuel: Approximately 34 gallons
Freshwater: Approximately 83 gallons
Holding tank: Approximately 21 gallons
Boat Pour is equipped with 12V DC and 110/115V AC electrical systems.
A major selling point is the upgraded electrical distribution panel installed in 2026. The updated panel provides modern circuit switching and digital system monitoring.
Electrical EquipmentUpgraded electrical panel installed in 2026
12V DC system
110/115V AC system
Dual 30-amp shore-power inlets
Shore-power cords
Three Group 31 AGM batteries replaced in October 2024
Dedicated starting and house-bank arrangement
Hitachi 80-amp high-output alternator
Mastervolt Powercharger 12/20-3 battery charger
ProWatt 600-watt inverter
Battery disconnect switches
AC and DC circuit protection
Digital electrical monitoring
Fuel and water level monitoring
12V outlets
LED interior lights
LED navigation lights
Engine-driven battery charging
Dockside battery charging
Shore-power water heating
Shore-powered reverse-cycle air conditioning
Boat Pour’s navigation and communication equipment is arranged between the helm and the interior navigation station.
Navigation ElectronicsGarmin GPSMAP 1243 multifunction display
Touchscreen chartplotter
Preloaded electronic chart capability
Sounder capability
Airmar multifunction transducer
Raymarine ST60 Tridata
Speed display
Depth display
Log information
Raymarine ST60 wind instrument
Raymarine multifunction display
Raymarine wheel-pilot autopilot
Raymarine course computer
AIS transceiver
Em-Trak B100 Class B AIS identified in the 2024 survey
Binnacle compass
Standard Horizon Matrix VHF radio
Standard Horizon RAM microphone at the helm
Approximately 26-inch television
Stereo system
Cabin and cockpit audio capability
LED cabin lighting
LED navigation lights
During the August 2024 sea trial, the Garmin display, VHF, helm microphone, Raymarine instruments, wind display, depth/speed equipment, and wheel-pilot autopilot were reported to power up and operate.
Boat Pour is fractional-sloop rigged with a conventional, fully battened mainsail and furling headsail.
Unlike an in-mast furling arrangement, her classic mast and Tides Marine Strong Track provide a direct, performance-oriented mainsail system while reducing friction during raising and lowering.
Mast and Standing RiggingFractional sloop rig
Classic anodized-aluminum mast
Deck/cabin-stepped mast
Double-spreader configuration
Stainless-steel compression post
Mast height: Approximately 50' 8"
Discontinuous 1x19 stainless-steel standing rigging
Upper and lower shrouds
Double backstays
Forestay incorporated into the furling system
Windex
Whisker pole
Rigid boom vang
Aluminum boom
The August 2024 survey reported no visible cracking at the inspected swaged terminals. The inspection was conducted from deck level and did not include a masthead inspection.
MainsailDacron mainsail
Fully battened
Tides Marine Strong Track
Mainsail cover
Traveler
Mainsheet system
Reefing lines
Halyard routed for cockpit management
120% Dacron genoa
Roller furling
Profurl furling system
Profurl C350 identified in the survey
Genoa UV cover
Adjustable genoa tracks and cars
Port and starboard genoa sheet leads
Two Harken 40.2 self-tailing primary winches
Harken 35.2 self-tailing halyard/cabin-top winches
Rope clutches
Cabin-top traveler
Rigid vang
Whisker pole
Running rigging led toward the cockpit
Wheel steering
Accessible helm controls
Her shoal-draft configuration draws approximately 4' 6", making her especially well suited to the Gulf Coast, Florida Keys, ICW, Bahamas, and other shallow-water cruising areas.
CockpitBoarding from the stern leads into a spacious aft cockpit with seating arranged to accommodate family and guests.
Cockpit features include:
Large self-draining cockpit
Port and starboard cockpit seating
Aft helm seat
Centerline wheel steering
Folding cockpit table
Blue bimini
Leather-wrapped wheel
Wheel cover
Winch covers
Pedestal-mounted navigation electronics
Engine controls at the helm
Compass
VHF RAM microphone
Cockpit shower
Cockpit lockers
Teak cockpit inlays and trim
Manual bilge-pump access
Walk-through transom
Folding/lifting helm seat
Integrated swim platform
Boarding ladder
The companionway has been upgraded with opening doors in place of the standard removable factory drop boards.
Additional features include:
Sliding companionway hatch
Hinged opening doors
Molded companionway steps
Stainless-steel grab rails
Engine access beneath the steps
Port and starboard side decks
Cabin-top handrails
Stainless-steel bow pulpit
Stainless-steel stern rails
Double lifelines
Port and starboard boarding gates
Deck-level fuel, water, and waste fills
Opening ports and hatches
Anchor locker
Foredeck working area
Genoa tracks and adjustable cars
Cabin-top traveler
Deck hardware and cleats
Six mooring cleats referenced in the survey
Bruce galvanized-steel claw anchor
Approximately 33 pounds
Chain and nylon rode
Stainless-steel bow roller
Self-draining anchor locker
Blue bimini
Cadet Grey canvas accents
Wheel cover
Mainsail cover
Winch covers
Genoa UV cover
Revere four-person liferaft
Liferaft reinspection/recertification required
Emergency tiller
Swim ladder
Fire extinguishers
Life jackets
Throwable flotation device
First-aid kit
Distress flares
Personal locator beacon identified in the 2024 survey
CO detectors
Bottom painted in 2023
Bottom reportedly cleaned approximately every six weeks
Shoal-draft cast-iron keel
Spade rudder
During the August 2024 haul-out, the surveyor reported the bottom to be in good overall condition. The rudder was sounded with no blistering or delamination found. The deck and superstructure were percussion sounded and moisture-meter tested, with no soft spots or excessive moisture reported.
Boat Pour was built by Beneteau America in Marion, South Carolina.
The Oceanis 34 was designed by Finot-Conq, with Jean-Marie Finot credited as naval designer and Nauta Design responsible for the interior.
Hull ConstructionSolid molded fiberglass hull
Hand-laid fiberglass construction
Fiberglass cloth, mat, and woven roving construction typical of the model
Gelcoat exterior finish
White exterior color
Structural fiberglass liner/grid
Marine-plywood bulkheads and partial bulkheads
Hull-to-deck joint secured with fasteners and adhesive
Monohull configuration
Spade rudder
Stainless-steel rudder stock
External cast-iron shoal-draft keel
Stainless-steel keel bolts
Bronze below-waterline through-hulls
Double-clamped underwater hose connections
Molded fiberglass deck and superstructure
Balsa-cored deck construction
Molded non-skid surfaces
Self-draining cockpit
Cabin-mounted handrails
Opening ports and hatches
Bonded structural liner system
CE Certified
Classification: A-6
The August 2024 survey reported the accessible keel bolts to be heavy-gauge stainless steel and in good condition. The accessible hull structure, keel area, rudder, deck, superstructure, grid system, and engine beds were inspected without evidence of delamination or excessive moisture.
Vessel name: Boat Pour
Builder: Beneteau America
Manufacturer: Beneteau
Model: Oceanis 34
Model year: 2011
Documented year: 2010
Category: Cruiser
Subcategory: Sloop
Condition: Used
Naval designer: Jean-Marie Finot / Finot-Conq
Interior designer: Nauta Design
Hull type: Monohull
Hull material: Fiberglass
Hull finish: Gelcoat
Exterior color: White
HIN: BEYKB056L011
CE Certified: Yes
Classification: A-6
Location: Bayou Grande Marina, Pensacola Naval Air Station, Pensacola, Florida
Asking price: $102,500
Length overall: 33' 11"
Length at waterline: 30' 8"
Beam: 12' 0"
Maximum draft: 4' 6"
Keel type: Shoal draft
Bridge clearance: 50'8"
Interior headroom: 6'3"
Displacement: 12,390 pounds
Ballast: 3,556 pounds
Cabins: Two
Heads: One
Sleeps: Six
Forward V-berth: One
Aft double berth: One
Salon single berths: Two
Air conditioning: Yes
Navigation station: Yes
Dinette: Yes
Electric head: Yes
Separate shower: Yes
Manufacturer: Yanmar
Model: 3YM30
Type: Inboard diesel
Horsepower: 29 HP
Output: Approximately 21.63 kW
Hours: Approximately 390
Serial number: 116851
Location: Middle/centerline beneath companionway
Propeller: Three-blade fixed bronze
Drive: Direct shaft
Shaft seal: Dripless
Fuel capacity: Approximately 34 gallons / 128.7 liters
Freshwater capacity: Approximately 83 gallons / 314.19 liters
Holding-tank capacity: Approximately 21 gallons / 79.49 liters
Propane stove
Propane oven
Front-loading 12V refrigerator
Contour microwave
Double stainless-steel sink
Hot and cold pressure water
115V/engine heat-exchanger water heater
Nauta-designed cabinetry
Countertop workspace
Storage lockers and cabinets
August 2024 pre-purchase survey
Market appraisal
Owner’s manual
Parts information
Model brochure and specifications
Preferred Yachts offers this listing on a 50-50 split with corresponding Florida licensed brokerages. Brokers unlicensed in Florida must contact listing broker to make arrangements that comply with Florida law.
Contact our team to schedule a private showing.